Installing an EzyJamb Frame

Note: Installers should download and fully review the EzyJamb ISD Installation Instructions and Datasheet prior to installation.

For more information, watch the video below or review the written instructions:

2 x ISD Stiles (1 x hinge side, 1 x latch side)

1 x ISD Header (Floor-to-ceiling, full-height doors will not include this section)

Hardware (hinges (per your order), screws, latch plate, dust box)

Hardware Packs:

• Hinges
• Screws (the relevant screws for AU will be packaged separately for concealed hinge orders)
• Cover plates (if concealed hinges)

Latch Kits:

• Latch plate
• Dust box
• Screws

1. Ensure that the stud opening is square and level and has the appropriate clearance for your specifications (see installation instructions).
2. Install the head piece, then use locator tabs to install stiles. Fasten hinge side, making sure jamb is level, then screw at 200mm centres up the stile, screwing back through plasterboard into the stud work. Double screw all ends and beside hinge position both above and below hinge.
3. Ensure that the two vertical sections are spaced evenly at the required distance.
4. Ensure the perforated side strips sit flat against the plasterboard to enable the jamb sections to be easily set into the wall surface. All the corners must be taped and plastered/jointed in. Finish the jamb with approved plaster/jointing compound. Hang the door in position leaving about 3mm clearance from the top and hinged side using the EzyJamb Standard or Concealed Hinges. Surface mount the striker plate into position to align with the latch plate punching.
5. Once the jamb is installed, hang the door with the help of a foot-operated door lifter to ensure proper fit of the jamb and hinges. Once adjusted, remove the door, plaster-in the jamb, sand down, and paint with the rest of the wall.
6. The door can now be re-hung for a seamless, flush finish.

RocYork Concealed Hinge Stud Opening Detail: Prepare a 25mm thick packer fixed to the hinge side of the jamb stud. Route the packer to create clearance cut-outs at hinge locations. The packer avoids cutting into the structural stud and maintains frame strength. Refer to the RocYork RY60 Installation Instructions document for more information.

Note: These instructions demonstrate the methods for installing an EzyJamb ISD as per the Australian specifications. Please view the USA EzyJamb ISD Installation Instructions if you are installing in North America.

Note: Installers should download and fully review the EzyJamb SRC Installation Instructions and Datasheet prior to installation.

For more information, watch the video below or review the written instructions:

2 x SRC Stiles (1 x hinge side, 1 x latch side)

1 x SRC Header

Hardware (hinges (per your order), screws, latch plate, dust box)

Hardware Packs:

• Hinges
• Screws (the relevant screws for AU will be packaged separately for concealed hinge orders)
• Cover plates (if concealed hinges)

Latch Kits:

• Latch plate
• Dust box
• Screws

1. Ensure that the stud opening is square and level and has the appropriate clearance for your specifications (see installation instructions).
2. Install head jamb first, then use locator tabs to install stiles. Fasten hinge side, making sure jamb is level. Then screw at 200mm centres up stile. Screw back through the plasterboard into the studwork. Double screw all ends and beside hinge position, both above and below hinge.
3. Ensure that the two vertical sections are spaced evenly at the required distance.
4. Ensure the perforated side strips sit flat against the plasterboard to enable the jamb sections to be easily set into the wall surface. All the corners must be taped and plastered/jointed in. Finish the jamb with approved plaster/jointing compound. Hang the door in position leaving about 3mm clearance from the top and the hinged side using the EzyJamb Standard or Concealed Hinges. Surface mount the striker plate into position to align with the latch plate punching.
5. Once the jamb is installed, hang the door with the help of a foot-operated door lifter to ensure proper fit of the jamb and hinges. Once adjusted, remove the door, plaster-in the jamb, sand down, and paint with the rest of the wall.
6. The door can now be re-hung for a seamless, flush finish.

RocYork Concealed Hinge Stud Opening Detail: Prepare a 25mm thick packer fixed to the hinge side of the jamb stud. Route the packer to create clearance cut-outs at hinge locations. The packer avoids cutting into the structural stud and maintains frame strength. Refer to the RocYork RY60 Installation Instructions document for more information.

Note: These instructions demonstrate the methods for installing an EzyJamb SRC as per the Australian specifications. Please view the USA EzyJamb SRC Installation Instructions if you are installing in North America.

Note: Installers should download and fully review the EzyJamb EZC Installation Instructions and Datasheet prior to installation.

For more information, watch the video below or review the written instructions:

2 x EZC (Section A or C) Jamb Sections (1 x hinge side, 1 x latch side)

2 x Reveals to Suit

1 x EZC Header (Section A or C) Jamb Section

1 x Reveal to Suit

2 x EZC Black Header Joiner Clips

Hardware (hinges (per your order), screws, latch plate, dust box)

Hardware Packs:

• Hinges
• Screws (the relevant screws for AU will be packaged separately for concealed hinge orders)
• Cover plates (if concealed hinges)

Latch Kits:

• Latch plate
• Dust box
• Screws

1. Ensure that the stud opening is square and level and has the appropriate clearance for your specifications (see installation instructions).
2. Join the two sections of the stile and fit the stile tightly over the wall. Fasten hinge side, making sure jamb is level and as tight against the stud opening as possible. Then screw at 200mm centres up the stile. Screw back through the plasterboard and into the stud work. Double screw all ends and beside the hinge position including both above and below the hinge.
3. Fit the final vertical section (strike jamb) into the head section joining clip. Ensure that the spacing between the two vertical sections are spaced evenly at the required distance.
4. Ensure the perforated side strips sit flat against the plasterboard to enable the jamb sections to be easily set into the wall surface. All corners MUST be taped and plastered/jointed. Finish the jamb with approved plaster/jointing compound.
5. Hang the door in position, leaving about 3mm clearance from the top and the hinged side using the EzyJamb Standard or Concealed Hinges. Surface mount the striker plate into position to align with the latch plate punching.
6. Once the jamb is installed, hang the door with the help of a foot-operated door lifter to ensure proper fit of the jamb and hinges. Once adjusted, remove the door, plaster-in the jamb, sand down, and paint with the rest of the wall.
7. The door can now be re-hung for a seamless, flush finish.

RocYork Concealed Hinge Stud Opening Detail: Prepare a 25mm thick packer fixed to the hinge side of the jamb stud. Route the packer to create clearance cut-outs at hinge locations. The packer avoids cutting into the structural stud and maintains frame strength. Refer to the RocYork RY60 Installation Instructions document for more information.

Note: These instructions demonstrate the methods for installing an EzyJamb EZC as per the Australian specifications. Please view the USA EzyJamb EZC Installation Instructions if you are installing in North America.